標題：帶電電纜識別儀生產廠家

產品概述

產品介紹：

帶電電纜識別儀生產廠家，在發射端采用單片機技術對發射信號進行編碼，驅動大口徑卡鉗發射平均值為0的大電流相位編碼信號。接收機中的單片機對接收的相位編碼信號解碼和相位識別。根據目標電纜上的信號相位特征的wei一性將目標電纜從一大束其它電纜中鑒別出來。帶電電纜識別儀也可以把輸出信號直接連接到停電運行的電纜上，這時可以識別接地回路達到1000歐姆以上。它是一種輕小型、緊湊型、便攜式儀器。適用于各種類型的高低壓動力電纜。

技術指標：

1、信號發生器：
①工作電源：AC 220V±10%  50Hz
②輸出功率：1kVA
③輸出信號：間隙調制信號
④間隙時間：1s～2s
⑤環境溫度：-10℃～45℃
2、信號檢測鉗
①電    源：無源工作
②鉗    口：開口時≥150mm，閉合時內徑：Φ120mm
③檢測方式：卡入閉合感應式，檢測方向及大小
④檢測電流：5A～40A
3、信號顯示器
①電    源：無源工作
②顯示方式：表頭指針擺動，表示方向和大小
③信號抑制調節：線性調節

主要特點：

帶電電纜識別儀生產廠家由電流脈沖發射機，接收機、收發卡鉗及若干連接導線組成。它具有大功率電流脈沖輸出;現場接收信號特征清晰，方便攜帶，輕便靈活，靈敏度高，能有效抑制現場工頻干擾，判斷準確、快速;保護電路可靠，不怕輸出短路;大鉗口ф150適合各種截面積的動力電纜;內部具有大功率隔離變壓器，操作者與市電不存在任何電氣上的直接接觸。但不允許在儀器帶電情況下用手去觸摸黑、紅夾子線。

工作原理：

由于正在運行的帶電電纜不允許破壞任何接地線等連接線，也不允許將識別儀發射機的輸出信號直接加在帶有高壓電的電纜相線上。帶電電纜識別，需要解決兩個難題，一是電纜識別信號如何耦合到電纜上的問題;二是耦合上去的信號一般比較小，而運行電纜可能存在50HZ不平衡電流、感應的50Hz干擾電流，電纜的分布電容電流等構成的50Hz工頻電磁干擾，高靈敏度接收卡鉗就存在如何抗50Hz工頻干擾問題。

我們研制的帶電電纜識別儀，發射和接收采用單片機編碼、解碼技術和廣泛應用在通信領域里的PSK技術。在發射卡鉗上發射平均值為0 的相位編碼信號，接收卡鉗中的單片機，對接收的信號經過硬件和如軟件的濾波后，再進行相位識別，當接收卡鉗按照電流方向卡電纜時，被識別的電纜電流表右偏，同時伴有聲光指示。而其它的電纜電流方向與被識別電纜的電流方向相反，其電流表指針左偏。沒有聲光指示。這就體現了被識別的目標電纜的wei一性。很容易將被識別電纜從多根電纜中區別開來。又由于被識別電纜上的信號電流強度全線都是一樣的，接收卡鉗在電纜沿線所接收到的電磁信號強度一致，從原理上講，識別的電纜不受被識別電纜長度的限制。